Tag Archives: refillable
Birm Refillable Filter Iron & Manganese Reduction Whole House Well Water Filter
Birm Refillable Filter Iron & Manganese Reduction Whole House Well Water Filter. This 4.5″ x 20″ premium birm refillable inline filter uses high grade filtration media for iron and manganese reduction. This birm filter is most often used to assist with iron and manganese reduction. An oxidizer can be used but is not necessary. This filter fits any standard housing made for 4.5″ x 20″ cartridges. Alkalinity should be greater than two times the combined sulfate and chloride concentration. Maximum water temp: 100o F/38o C. Water pH range: 6.8-9.0. Content must be equal to at least 15% of the iron (or iron and manganese) content. Service flow rate: 3.5-5 gpm/sq. Intermittent flow rates and/or favorable local conditions may allow higher flow rates. Highest grade Birm filtration media available- for the reduction of iron, manganese. Granular filter media commonly used for the reduction of iron and/or manganese from water supplies. Great for Well Water Sources. Refillable filter cartridge 4.5″ x 20″. Compatible with most standard 20 Big Blue Whole House Water System. California, Connecticut, District of Columbia, Massachusetts, Louisiana, Maryland, Mississippi, Tennessee, Washington, New Mexico, Illinois. Most items are forwarded to our supplier for processing, which will then be fulfilled through a distributor that is closest to your location. Ese distributors may be names you recognize or sourced from smaller local operations. Any product you return must be in the same condition you received it and in the original packaging. We usually respond within 24 hours on weekdays. Thank you for shopping at our store.
2 Stage Standard 10 Car Wash Spotless Water System with DI Refillable Cartridges
2 Stage10 Inch Whole House Car Wash Spotless Water System w/ Dual 10″x 2.5″ Mixed Bed DI Resin Filter Cartridges. This Car Wash Filter System removes all of its mineral ions, which produces high-purity water without the scale buildup. This Dual DI System can effectively filter out mineral ions such as sodium, calcium, iron, copper, chloride, sulfate, nitrates, phosphates, silica, and ammonia to deliver clean and spotless water to your water hose. This systems is post auto-detailing / Window cleaning system. Bulk Media for Refillable Cartridges. Five pounds of resin is enough to refill an 2 inch x10 inch in-line refillable filter housing about 10 times or 2.5 inch x 10 inch refillable filter (for standard 10 inch housing) about 7 times. According to the incoming PPM to the filter. 5 ppm – 2000 gallons. 10 ppm – 1000 gallons. 50 ppm – 200 gallons. 100 ppm – 100 gallons. 200 ppm -50 gallons. 300 ppm – 35 gallons. 400 ppm – 25 gallons. 500 ppm – 20 gallons. Bad tastes & Odors. Chemicals & organic impurities. 2 Stage White Steel Mounting Bracket. Set of 2 filters: 2 x Refillable Mixed Bed Deionization (DI) Filters. Filter cartridges should be changed every 1 to 12 months under domestic conditions. Varies & depend on the water incoming (source) water quality & gallons you use per day/month. But you can keep in service for maximum 12 months. 2 Standard Filter housings 3/4 inch NPT (Accept Standard filters 9.75 x 2.5 inch). Opening Spanner / Wrench. Installation instruction are included. This system could start to generate the pure water at 20PSI. Maximum recommended working pressure: 90 PSI. Maximum Operating Temperature: 125°F (52°C). Dimensions: H 15 inch x Length 9.5 inch x W 5 inch. Weight: 10 lbs Approx. The item “2 Stage Standard 10 Car Wash Spotless Water System with DI Refillable Cartridges” is in sale since Friday, June 4, 2021. This item is in the category “Home & Garden\Kitchen, Dining & Bar\Small Kitchen Appliances\Water Purification\Water Filters”. The seller is “max.water.usa” and is located in Tonawanda, New York. This item can be shipped worldwide.
- Model: 103215~104023×2
- Country/Region of Manufacture: Canada
- Custom Bundle: No
- Item Depth: 6 in
- Number of Filtration Stages: 3 stages
- Compatible Brand: Max Water
- Material: Plastic
- Filtration Method: Polypropylene
- Type: Standard Whole House Filter System
- Number in Pack: 2
- Compatible Model: Max Water
- Color: Multicolor, Clear
- MPN: 103215~104023×2
- Contaminant Removal: Sediment
- Country of Manufacture: Canada
- Brand: Max Water
- Suitable For: Commercial
- Manufacturer Color: Multicolor, Clear
1.5 Cubic Foot Coconut Carbon Media Whole House Systems Or Refillable Cartridges
REPLACEMENT CARBON MEDIA FOR WHOLE HOUSE SYSTEMS. OR USE FOR REFILLABLE CARTRIDGES. Periodically, you are going to have to replace the media in your system. It may be years down the road if you have a new one, but you might want to know how. It’s fairly easy to do, and a great DIY project. It’s not rocket science! If you have an older system that is not performing like it used to, it is time to change the media. They last much much longer than that, unless you’ve abused it, or the threads are damaged, it is generally not an item that needs to be replaced. Do inspect it carefully though. The two things that can go wrong is, as we mentioned, media that is exhausted, or your control valve is malfunctioning. First of all, turn on the water by-pass valve on your system so that you can work on it. You will want to relieve the water pressure still in the unit, turn the control to “backwash” for 30 secs, so the system purges some water and pressure. There should be no water coming out of the drain after the first few seconds if your by pass valve is on. Put the control back into service mode. Unplug the electricity, remove the pipe fittings to your unit. Once your filter is free from your plumbing, unscrew the control valve. You will probably need someone to hold the unit while you unscrew it. Once it unscrews, you will notice that it is attached to the distributer/riser tube. This tube is attached to the control valve by an o-ring, so pull up on it. If the tube comes up with it, don’t worry, just grab on to it and separate them. Put the control valve away from where you are working. You don’t want to get media or dirt into it. The unit is heavy with water and media. You may want to move it, in which case, siphon the water out. If your distribution/ riser tube is not too far out of the tank, insert a lenght of hose down the tube to siphon out the water. With the tank now considerably lighter, pull out the distributor/riser tube and dump out the old media and dispose of properly. Clean out your media tank. Wash it with a bleach solution. If your media needed to be replaced because of fouling, this is especially important. Don’t forget to clean the distributor/riser tube as well. Once it’s clean and dry, we are ready to rebuild. Center your distributer/riser tube in the tank. There is a shallow indentation at the bottom of the tank it fits in. The bulb part goes in the bottom! Cover the opening of the distributer/riser tube with a plug or a piece of plastic securely rubber-banded to the tube. You DO NOT want any of the media in that tube, it will find it’s way into the control valve and cause it to malfunction. Now you are ready to rebed the filter. Use a funnel and add the media to the tank. Keeping the distributer/riser tube centered. It may be easier to add it slowly, rather than pouring it directly from the heavy bag. The media is never the entire depth of the tank, there is always at least half to a third empty space to provide plenty of room for backwashing. Some media like Filtersorb will be even less. When you’ve added all the media to the tank, clean off the protective cap/cover on your distributer/riser tube, and then remove it. Put a little food grade silicone grease on the O-ring in your control valve, the one that holds the distributer/riser tube in place. Insert the control head on to the riser tube and push down so it forms a nice seal. Screw the control valve back on, attach your plumbing, and plug in the control valve. Open a faucet down stream from the filter to purge the air that will be in the system from the newly rebuilt filter. Turn on the water S-L-O-W-L-Y to the filter, take your time. The water may be discolored, especially if it’s carbon that you’ve replaced. The purging air will be noisy… Don’t freak out! Once all the air is purged, let it sit for a few hours or overnight. It’s OK to keep using water during this time, you’ll see some discoloration, but it’s just aesthetics. Now it’s time to put it through a back wash cycle to remove media dust, and if it’s softener media or other media that needs to be regenerated, this is the time to do it. Make sure you have a faucet opened downstream in case there is still some trapped air in the system. Put the filter through an entire cycle to clean it all up and to regenerate. With a carbon filter, there will still be some residual carbon fines in the water for a few days after a backwash, again, that’s normal. Make sure the valve is working correctly and there are no leaks. Please keep all your package in addition to the products. International Buyers Please Note. We do not mark merchandise values below value or mark items as “gifts” – US and International government regulations prohibit such behavior. (REVERSE OSMOSIS) DRINKING WATER SYSTEM. Drinking Water System when installed and operated within recommended parameters, with the exceptions stated below. How Long Does The Coverage Last? Drinking Water System that is damaged because of neglect, misuse, alterations accident, misapplication, physical damage, or damage caused by fire, acts of God, freezing or hot waters or similar causes. The item “1.5 CUBIC FOOT COCONUT CARBON MEDIA WHOLE HOUSE SYSTEMS OR REFILLABLE CARTRIDGES” is in sale since Saturday, July 9, 2016. This item is in the category “Home & Garden\Home Improvement\Plumbing & Fixtures\Water Filters”. The seller is “waterprousa” and is located in Corona, California. This item can be shipped to United States.
- Brand: Water Pro Shop
- MPN: Does Not Apply