Tag Archives: port
2 Stage Whole House Water Filter System with 10-Inch Blue Housing-1 Port
Maximum Pressure: 90 psi (6.2 bar) Temperature:40-110°F/5-45°C Shelf life: 5 Years More valuable information. What is dimension of the big blue housing and carbon filter? It is 4.5″OD x 10″ height. What is in the box? 2×10 inch blue housing with pressure release and 1inch NPT, 2x plastic wrench, 2x metal bracket. 1x PP sediment filter, 1x carbon block filter. What is filters options? PP spun filter, Remove sand, dirt, sediment. Life time:6 months. Granular activited carbon filter, Remove chlorine, taste & odors, very fine particulates. Carbon block filter, Further remove chlorine, taste & odors, very fine particulates. PP pleated filter, the material is same as PP sediment, Remove sand, dirt, sediment. The Life Time of the Filter Cartridge Depends on Usage Amount and Feed Water Quality. Please lubricate the o-ring with silicon grease and use wrench provided to prevent leakage. Protect filter housing from freezing. The rubber o-ring provides the water tight seal between the cap and the sump. It is important that the o-ring be properly SEATED IN THE GROOVE of a water leak could occur. 2 Stage Whole House Water Filtration System with 5 Micron PP Sediment and Carbon Block Filter, 10 inch blue housing (1NPT brass inlet/outlet), plastic wrench and screws It is Installed at the main water supply and produce pure water for your entire home. Enjoy better water from every tap and every appliance in the whole house FUNCTION-PP Sediment is used to reduce silt, sand, rust, dirt, The PP filter display different color and tracks the life time as you use, It is time to replace a new one when it is dark yellow or brown. Carbon block filter is used to reduce chlorine, taste & odors Large capacity housing for high flow applications, Flow rate : 5-15 GPM (Depend on Feed Water Pressure) LIFE TIME:6-12 months or 100K gallons water. Note:this system will NOT reduce Total Dissolved Solids (TDS), but keeps healthy minerals in your water. If you are searching for a filter that reduce TDS, Please refer Reverse Osmosis systems.
3-Stage 20×4.5 Big Blue Whole House Water Filter System 1 NPT Port 150000 Gal
SimPure SPWH-3S 20″ x 4.5″ 3 Stage Big Blue Whole House Water Filtration System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges – GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure SPWH-3S 3 Stage Big Blue Whole House Water Filter System. The SimPure SPWH-3S is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install SPWH-3S 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This SPWH-3S water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure SPWH-3S Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles, etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread BRASS PORT connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Temperature Range: 41-100? (5-38?). Pressure Range: 25 – 90 psi. 1x SPWH-3S assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean. SERVING USA SINCE 2006. SimPure dedicated in providing world-class quality of water filtration solutions. Please contact our trained water specialists. And is available to answer any questions during the life of the product.
2Stage Whole House Water Filter System for 4.5×10 Filtration Cartridge 1 Port
SimPure SPWH-2S 10″ x 4.5″ 2 Stage Whole House Water Filtration System (1 Inlet/Outlet Port) with Big Housings & Pressure Relief Valve- GAC Filter, Carbon Block, Sediment Filter Cartridges – Remove Silt, Sand, Rust, Dirt, Chlorine, Taste & Odors, Iron, Lead, Manganese – Whole Home/Pool/Well/Farm Water Filters Portable Steal Frame. SimPure SPWH-2S 2 Stage Big Blue 10″x4.5″ Whole House Water Filter System. The SimPure SPWH-2S is a 2 Stage Whole House Filtration System(PP Sediment + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. Clear Housing is convenient to indicate and track of your filter life. Enjoy better water from every tap and every appliance in the whole house. With our instruction you can use and install SPWH-2S 2-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Clear Housing help you to know which filter and when you need to change. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This SPWH-2S water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure SPWH-2S Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Big Clear Housing let you know when to replace the filters. The pressure relief Valve: Let you replace the filter cartridges easily. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 10 4.5 Inch. Filter Life (Months): 6-12 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Temperature Range: 41-100? (5-38?). Pressure Range: 25 – 90 psi. 1x SPWH-2S assembled housing kit with bracket. 2x Installed Filters(PP sediment+CTO filters). 2x Plastic Expansion Nail. 4x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q:Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. The O-ring may not be in place. A2: O-ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Check the filter cartridge has not been installed incorrectly. Make sure the plastic wrapper around the filter has been removed. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.
Whole House 3-Stage Water Filtration System, 3/4? Port with 2 valves + extra set
VOCs (Volatile Organic Compounds). Chemicals & Organic Impurities. 1 x Three-Stage White Steel Mounting Bracket with Pre-installed Filter Cartridges. 1 x Extra Set of 3 Filters (for up to 6 months of use). 3 x Standard Filter Housings (3/4 inch NPT). 2 x 3/4″x3/4″ Fittings (nipples). 2 x On/Off Valves. Minimum Operating Pressure: 20 PSI. Maximum Working Pressure: 85 PSI. Maximum Operating Temperature: 100°F (52°C). System Dimensions: 15″ (Height) x 15″ (Width) x 6 (Depth). Flow Rate: 1 to 8 GPM. Flow rate may vary based on incoming water pressure and quality.
3 Green High Capacity 10 x 4.5 Whole House Filter Purifier System 1 Brass Port
High Capacity 10 x 4.5″ Whole House Filter Purifier System for Well or City Water, Presser Relief Button, 1″ NPT Brass Port, Double O-Ring, Meets NSF Standards & Regulations (Green, 3 Sets). DURABLE STRUCTURE: 10″x 4.5″ Green Housing Set is proper for high-flow applications. The housing body is made of reinforced polypropylene for strength & resistance to chemicals, the black cap is made of high-flow polypropylene for toughness. Food grade material makes all filtered water is safe & healthy. The cap has 1 inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. This unit is appropriate for well water, commercial & industrial filtration. POINT OF USE: Those Housings for use in various high-flow applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, well water filtration, food service, and irrigation. Extends life of Washing Machines, Water Heaters & Other Household Appliances Keeps water fresh by reducing and removing iron, manganese, chlorine, hydrogen sulfide, herbicides, pesticides, and other industrial chemicals. EASY TO OPERATE: There are 2 rubber O-rings on the top of the housing body to ensure a watertight seal. Such design allowed properly seal cap and housing body to prevent water leakage when you replace cartridge. The built-in red pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. According to system size leave 4 inches free space should be left between bottom of the system and floor to allowed easy filter cartridge replacement. WELL-MATCHED MODELS OF HOUSINGS: BIG-CLEAR-LX-10 and A48249, Aqua Filter Plus 150237-INSTKIT, BLUONICS BLBB20GAC, BLBBC10 and BLBB10x2, iSpring HB18B, OMNIFilter BF7-S-05 and BF7-S-S06, American Plumber W10-PR, Watts W10FFPH1CBPR, SimPure RSWHB001Z_S8, AB-WH10BBN, Geekpure BB-10T and BB-10B, EcoPure EPWO4, Culligan HD-950A, Aquaboon AB-WH10BB-1S10BB5M. The 10″x 4.5″ Green High Capacity Housing for Whole House Water Filtration System with 1 Inlet / Outlet Ports (RA-HS-6T) is proper to use for reducing sediment, dirt, rust, & suspended particles in incoming water to you house. The green housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the black cap is made of high-flow polypropylene for toughness. The black cap has 1 inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. The Double rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. Those Housings for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, food service, and irrigation. Easy to connect multiply housings in one Custom Whole House Water Filtration System to fit your specific needs. WARNING: OPERATING PRESSER NO MORE THAN 60 PSI. 1O x 4.5 Polypropylene Sediment Cartridge. 1O x 4.5 Pleated Washable & Reusable Sediment Cartridge. 1O x 4.5 Coconut Shell Carbon Block Cartridge. 1O x 4.5 Granular Activated Carbon Cartridge. Sediment Filter is often the first filter installed in the Whole House Water Filter circuit. It is often the first point of contact between your water supply and your home and is used as a pre-filtration unit before the water continues to reverse osmosis and activated carbon filters. It catches unwanted particles, including sand, dirt, silt, rust, and other fine particles as they attempt to enter your house’s water system. These particles and pollutants come from water sources, old and dirty pipes, as well as contaminants that are used to treat the water. 10″ x 4.5″ filters are made of fine-melted polypropylene that are blown and spun into cylinder-like form. Removal of these particles allows filters, such as Carbon Block or GAC (Granular Activated Carbon) filters, as well as household water appliances like boilers, refrigerators, ice-makers, and many more, to perform better for longer periods of time. Pleated sediment water filters reduces sand, dirt, silt, rust, & scale particles in residential and commercial water. Pleated filters are made of resin-impregnated cellulose and polyester media pleated around a polypropylene core for strength. These materials trap suspended particles, materials that block microbes and adsorb unwanted chemicals or substances that cause a chemical change to the water, such as acid neutralization. The pleated design provides an amplified surface area that may extend the filter’s life while removing undesirable particles and chemicals from the water by means of a semipermeable barrier, adsorption, & biological processes. Those filters are washable & reusable. Advantage of pleated filters is that they protect against a lower pressure drop & allow increased water flow rates. Pleated cartridges outperform standard wound, spun, & melt blown filters because of their re-usability. Activated Carbon Block filters are made of fine coconut shell carbon. They remove odors, undesirable colors, and unpleasant tastes of many organic compounds. These filters also are effective in removing chemicals like iron, manganese, chlorine, and hydrogen sulfide from your water to name a few. By removing these unwanted byproducts, you can rest assured that you will have access to fresh and clean water. Since these filters are made of a finely packed carbon (forming a cylinder block), they offer a much finer filtration of suspended particles and dirt. Chlorine removal is what carbon is best at, and nothing else equals carbon’s ability to remove chlorine. Granular Activated Carbon filters are made of fine coconut shell carbon. All Ronaqua GAC filters are made with high quality coconut shell carbon crushed into positively charged granules. The positively charged granules in the filter remove negative ions from the water, such as: chlorine, fluorides, ozone, and dissolved organic solutes, effectively providing good general-purpose drinking water. High Capacity 10 x 4.5 Whole House Filter Purifier System can purify the water coming into your home for Well Water and Municipal Tap Water. It can deliver effective protection for the pipeline, water purifier, water heater, wall hung gas boiler, washing machine, dishwashers, showers, and other terminal water appliances. Protect Your Home and Appliances. Improve Your Life by Providing Clean Drinking Water. Forget about dirty bad-smell and bad-tasting water. High capacity water filtration system will efficiently remove sediment, large and fine particles, chlorine, odors, and tastes of many organic compounds extend the service life of water heaters, washing machine, dishwashers, reverse osmosis systems, and all plumbing fixtures. Our individually designed whole house water filtration system by removing, chlorine, and other contaminants, provide clean and fresh water for your family, protect your loved ones, and reduce the use of bottled water. We are proud to deliver the perfect water your household and safe our Planet by reducing use of the plastic bottles. These housings made from food grate material and meet NSF (National Science Foundation) standards and regulations. Tanks to durable construction, and easy maintenance those housings can be used in many different applications.
4 White High Capacity 10 x 4.5 Whole House Filter Purifier System 1 Brass Port
High Capacity 10 x 4.5″ Whole House Filter Purifier System for Well or City Water, Presser Relief Button, 1″ NPT Brass Port, Double O-Ring, Meets NSF Standards & Regulations (White , 4 Sets). DURABLE STRUCTURE: 10″x 4.5″ White Housing Set is proper for high-flow applications. The housing body is made of reinforced polypropylene for strength & resistance to chemicals, the black cap is made of high-flow polypropylene for toughness. Food grade material makes all filtered water is safe & healthy. The cap has 1 inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. This unit is appropriate for well water, commercial & industrial filtration. POINT OF USE: Those Housings for use in various high-flow applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, well water filtration, food service, and irrigation. Extends life of Washing Machines, Water Heaters & Other Household Appliances Keeps water fresh by reducing and removing iron, manganese, chlorine, hydrogen sulfide, herbicides, pesticides, and other industrial chemicals. EASY TO OPERATE: There are 2 rubber O-rings on the top of the housing body to ensure a watertight seal. Such design allowed properly seal cap and housing body to prevent water leakage when you replace cartridge. The built-in red pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. According to system size leave 4 inches free space should be left between bottom of the system and floor to allowed easy filter cartridge replacement. WELL-MATCHED MODELS OF HOUSINGS: BIG-CLEAR-LX-10 and A48249, Aqua Filter Plus 150237-INSTKIT, BLUONICS BLBB20GAC, BLBBC10 and BLBB10x2, iSpring HB18B, OMNIFilter BF7-S-05 and BF7-S-S06, American Plumber W10-PR, Watts W10FFPH1CBPR, SimPure RSWHB001Z_S8, AB-WH10BBN, Geekpure BB-10T and BB-10B, EcoPure EPWO4, Culligan HD-950A, Aquaboon AB-WH10BB-1S10BB5M. The 10″x 4.5″ White High Capacity Housing for Whole House Water Filtration System with 1 Inlet / Outlet Ports (RA-HS-6T) is proper to use for reducing sediment, dirt, rust, & suspended particles in incoming water to you house. The white housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the black cap is made of high-flow polypropylene for toughness. The black cap has 1 inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. The Double rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. Those Housings for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, food service, and irrigation. Easy to connect multiply housings in one Custom Whole House Water Filtration System to fit your specific needs. WARNING: OPERATING PRESSER NO MORE THAN 60 PSI. 1O x 4.5 Polypropylene Sediment Cartridge. 1O x 4.5 Pleated Washable & Reusable Sediment Cartridge. 1O x 4.5 Coconut Shell Carbon Block Cartridge. 1O x 4.5 Granular Activated Carbon Cartridge. Sediment Filter is often the first filter installed in the Whole House Water Filter circuit. It is often the first point of contact between your water supply and your home and is used as a pre-filtration unit before the water continues to reverse osmosis and activated carbon filters. It catches unwanted particles, including sand, dirt, silt, rust, and other fine particles as they attempt to enter your house’s water system. These particles and pollutants come from water sources, old and dirty pipes, as well as contaminants that are used to treat the water. 10″ x 4.5″ filters are made of fine-melted polypropylene that are blown and spun into cylinder-like form. Removal of these particles allows filters, such as Carbon Block or GAC (Granular Activated Carbon) filters, as well as household water appliances like boilers, refrigerators, ice-makers, and many more, to perform better for longer periods of time. Pleated sediment water filters reduces sand, dirt, silt, rust, & scale particles in residential and commercial water. Pleated filters are made of resin-impregnated cellulose and polyester media pleated around a polypropylene core for strength. These materials trap suspended particles, materials that block microbes and adsorb unwanted chemicals or substances that cause a chemical change to the water, such as acid neutralization. The pleated design provides an amplified surface area that may extend the filter’s life while removing undesirable particles and chemicals from the water by means of a semipermeable barrier, adsorption, & biological processes. Those filters are washable & reusable. Advantage of pleated filters is that they protect against a lower pressure drop & allow increased water flow rates. Pleated cartridges outperform standard wound, spun, & melt blown filters because of their re-usability. Activated Carbon Block filters are made of fine coconut shell carbon. They remove odors, undesirable colors, and unpleasant tastes of many organic compounds. These filters also are effective in removing chemicals like iron, manganese, chlorine, and hydrogen sulfide from your water to name a few. By removing these unwanted byproducts, you can rest assured that you will have access to fresh and clean water. Since these filters are made of a finely packed carbon (forming a cylinder block), they offer a much finer filtration of suspended particles and dirt. Chlorine removal is what carbon is best at, and nothing else equals carbon’s ability to remove chlorine. Granular Activated Carbon filters are made of fine coconut shell carbon. All Ronaqua GAC filters are made with high quality coconut shell carbon crushed into positively charged granules. The positively charged granules in the filter remove negative ions from the water, such as: chlorine, fluorides, ozone, and dissolved organic solutes, effectively providing good general-purpose drinking water. High Capacity 10 x 4.5 Whole House Filter Purifier System can purify the water coming into your home for Well Water and Municipal Tap Water. It can deliver effective protection for the pipeline, water purifier, water heater, wall hung gas boiler, washing machine, dishwashers, showers, and other terminal water appliances. Protect Your Home and Appliances. Improve Your Life by Providing Clean Drinking Water. Forget about dirty bad-smell and bad-tasting water. High capacity water filtration system will efficiently remove sediment, large and fine particles, chlorine, odors, and tastes of many organic compounds extend the service life of water heaters, washing machine, dishwashers, reverse osmosis systems, and all plumbing fixtures. Our individually designed whole house water filtration system by removing, chlorine, and other contaminants, provide clean and fresh water for your family, protect your loved ones, and reduce the use of bottled water. We are proud to deliver the perfect water your household and safe our Planet by reducing use of the plastic bottles. These housings made from food grate material and meet NSF (National Science Foundation) standards and regulations. Tanks to durable construction, and easy maintenance those housings can be used in many different applications.
4 Green High Capacity 10 x 4.5 Whole House Filter Purifier System 1 Brass Port
High Capacity 10 x 4.5″ Whole House Filter Purifier System for Well or City Water, Presser Relief Button, 1″ NPT Brass Port, Double O-Ring, Meets NSF Standards & Regulations (Green, 4 Sets). DURABLE STRUCTURE: 10″x 4.5″ Green Housing Set is proper for high-flow applications. The housing body is made of reinforced polypropylene for strength & resistance to chemicals, the black cap is made of high-flow polypropylene for toughness. Food grade material makes all filtered water is safe & healthy. The cap has 1 inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. This unit is appropriate for well water, commercial & industrial filtration. POINT OF USE: Those Housings for use in various high-flow applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, well water filtration, food service, and irrigation. Extends life of Washing Machines, Water Heaters & Other Household Appliances Keeps water fresh by reducing and removing iron, manganese, chlorine, hydrogen sulfide, herbicides, pesticides, and other industrial chemicals. EASY TO OPERATE: There are 2 rubber O-rings on the top of the housing body to ensure a watertight seal. Such design allowed properly seal cap and housing body to prevent water leakage when you replace cartridge. The built-in red pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. According to system size leave 4 inches free space should be left between bottom of the system and floor to allowed easy filter cartridge replacement. WELL-MATCHED MODELS OF HOUSINGS: BIG-CLEAR-LX-10 and A48249, Aqua Filter Plus 150237-INSTKIT, BLUONICS BLBB20GAC, BLBBC10 and BLBB10x2, iSpring HB18B, OMNIFilter BF7-S-05 and BF7-S-S06, American Plumber W10-PR, Watts W10FFPH1CBPR, SimPure RSWHB001Z_S8, AB-WH10BBN, Geekpure BB-10T and BB-10B, EcoPure EPWO4, Culligan HD-950A, Aquaboon AB-WH10BB-1S10BB5M. The 10″x 4.5″ Green High Capacity Housing for Whole House Water Filtration System with 1 Inlet / Outlet Ports (RA-HS-6T) is proper to use for reducing sediment, dirt, rust, & suspended particles in incoming water to you house. The green housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the black cap is made of high-flow polypropylene for toughness. The black cap has 1 inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. The Double rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. Those Housings for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, food service, and irrigation. Easy to connect multiply housings in one Custom Whole House Water Filtration System to fit your specific needs. WARNING: OPERATING PRESSER NO MORE THAN 60 PSI. 1O x 4.5 Polypropylene Sediment Cartridge. 1O x 4.5 Pleated Washable & Reusable Sediment Cartridge. 1O x 4.5 Coconut Shell Carbon Block Cartridge. 1O x 4.5 Granular Activated Carbon Cartridge. Sediment Filter is often the first filter installed in the Whole House Water Filter circuit. It is often the first point of contact between your water supply and your home and is used as a pre-filtration unit before the water continues to reverse osmosis and activated carbon filters. It catches unwanted particles, including sand, dirt, silt, rust, and other fine particles as they attempt to enter your house’s water system. These particles and pollutants come from water sources, old and dirty pipes, as well as contaminants that are used to treat the water. 10″ x 4.5″ filters are made of fine-melted polypropylene that are blown and spun into cylinder-like form. Removal of these particles allows filters, such as Carbon Block or GAC (Granular Activated Carbon) filters, as well as household water appliances like boilers, refrigerators, ice-makers, and many more, to perform better for longer periods of time. Pleated sediment water filters reduces sand, dirt, silt, rust, & scale particles in residential and commercial water. Pleated filters are made of resin-impregnated cellulose and polyester media pleated around a polypropylene core for strength. These materials trap suspended particles, materials that block microbes and adsorb unwanted chemicals or substances that cause a chemical change to the water, such as acid neutralization. The pleated design provides an amplified surface area that may extend the filter’s life while removing undesirable particles and chemicals from the water by means of a semipermeable barrier, adsorption, & biological processes. Those filters are washable & reusable. Advantage of pleated filters is that they protect against a lower pressure drop & allow increased water flow rates. Pleated cartridges outperform standard wound, spun, & melt blown filters because of their re-usability. Activated Carbon Block filters are made of fine coconut shell carbon. They remove odors, undesirable colors, and unpleasant tastes of many organic compounds. These filters also are effective in removing chemicals like iron, manganese, chlorine, and hydrogen sulfide from your water to name a few. By removing these unwanted byproducts, you can rest assured that you will have access to fresh and clean water. Since these filters are made of a finely packed carbon (forming a cylinder block), they offer a much finer filtration of suspended particles and dirt. Chlorine removal is what carbon is best at, and nothing else equals carbon’s ability to remove chlorine. Granular Activated Carbon filters are made of fine coconut shell carbon. All Ronaqua GAC filters are made with high quality coconut shell carbon crushed into positively charged granules. The positively charged granules in the filter remove negative ions from the water, such as: chlorine, fluorides, ozone, and dissolved organic solutes, effectively providing good general-purpose drinking water. High Capacity 10 x 4.5 Whole House Filter Purifier System can purify the water coming into your home for Well Water and Municipal Tap Water. It can deliver effective protection for the pipeline, water purifier, water heater, wall hung gas boiler, washing machine, dishwashers, showers, and other terminal water appliances. Protect Your Home and Appliances. Improve Your Life by Providing Clean Drinking Water. Forget about dirty bad-smell and bad-tasting water. High capacity water filtration system will efficiently remove sediment, large and fine particles, chlorine, odors, and tastes of many organic compounds extend the service life of water heaters, washing machine, dishwashers, reverse osmosis systems, and all plumbing fixtures. Our individually designed whole house water filtration system by removing, chlorine, and other contaminants, provide clean and fresh water for your family, protect your loved ones, and reduce the use of bottled water. We are proud to deliver the perfect water your household and safe our Planet by reducing use of the plastic bottles. These housings made from food grate material and meet NSF (National Science Foundation) standards and regulations. Tanks to durable construction, and easy maintenance those housings can be used in many different applications.
3 Packs 20-Inch Heavy Duty Big Whole House Water Filter Housing 1 Port
Complete set 20 inch whole house water filter housing. With plastic wrench, screw and metal bracket. Pack of 3 set in the box. Equip with pressure release button for high pressure. Please refer above photo. COMPLETE -Complete one set 20 inch big jumbo housing, 1NPT inlet/outlet, with pressure release button for high flow, plastic wrench and metal bracket. STANDARD -Fits all standard sized 4-1/2 inch diameter industry 20 inch whole house cartridges. HIGH QUALITY -Fits NSF standard, Large capacity housing for high flow applications. Maximum Pressure: 90 psi (6.2 bar). Shelf life: 5 Years. What is dimension of this housing? It is 4.5″OD x 20″ height. What is in the box? 3pc x 20-inch housing with pressure release, 3pc plastic wrench, 3pc metal bracket, bracket screws(not include expansion screw). What is filters options? PP spun filter, reduces sand, dirt, sediment. Life time:6 months. Carbon block filter, reduces specific contaminants. The Life Time of the Filter Cartridge Depends on Usage Amount and Feed Water Quality. Please lubricate the o-ring with silicon grease and use wrench provided to prevent leakage. Protect filter housing from freezing. The rubber o-ring provides the water tight seal between the cap and the sump. It is important that the o-ring be properly SEATED IN THE GROOVE of a water leak could occur.
3 White High Capacity 10 x 4.5 Whole House Filter Purifier System 1 Brass Port
High Capacity 10 x 4.5″ Whole House Filter Purifier System for Well or City Water, Presser Relief Button, 1″ NPT Brass Port, Double O-Ring, Meets NSF Standards & Regulations (White , 3 Sets). DURABLE STRUCTURE: 10″x 4.5″ White Housing Set is proper for high-flow applications. The housing body is made of reinforced polypropylene for strength & resistance to chemicals, the black cap is made of high-flow polypropylene for toughness. Food grade material makes all filtered water is safe & healthy. The cap has 1 inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. This unit is appropriate for well water, commercial & industrial filtration. POINT OF USE: Those Housings for use in various high-flow applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, well water filtration, food service, and irrigation. Extends life of Washing Machines, Water Heaters & Other Household Appliances Keeps water fresh by reducing and removing iron, manganese, chlorine, hydrogen sulfide, herbicides, pesticides, and other industrial chemicals. EASY TO OPERATE: There are 2 rubber O-rings on the top of the housing body to ensure a watertight seal. Such design allowed properly seal cap and housing body to prevent water leakage when you replace cartridge. The built-in red pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. According to system size leave 4 inches free space should be left between bottom of the system and floor to allowed easy filter cartridge replacement. WELL-MATCHED MODELS OF HOUSINGS: BIG-CLEAR-LX-10 and A48249, Aqua Filter Plus 150237-INSTKIT, BLUONICS BLBB20GAC, BLBBC10 and BLBB10x2, iSpring HB18B, OMNIFilter BF7-S-05 and BF7-S-S06, American Plumber W10-PR, Watts W10FFPH1CBPR, SimPure RSWHB001Z_S8, AB-WH10BBN, Geekpure BB-10T and BB-10B, EcoPure EPWO4, Culligan HD-950A, Aquaboon AB-WH10BB-1S10BB5M. The 10″x 4.5″ White High Capacity Housing for Whole House Water Filtration System with 1 Inlet / Outlet Ports (RA-HS-6T) is proper to use for reducing sediment, dirt, rust, & suspended particles in incoming water to you house. The white housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the black cap is made of high-flow polypropylene for toughness. The black cap has 1 inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. The Double rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. Those Housings for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, food service, and irrigation. Easy to connect multiply housings in one Custom Whole House Water Filtration System to fit your specific needs. WARNING: OPERATING PRESSER NO MORE THAN 60 PSI. 1O x 4.5 Polypropylene Sediment Cartridge. 1O x 4.5 Pleated Washable & Reusable Sediment Cartridge. 1O x 4.5 Coconut Shell Carbon Block Cartridge. 1O x 4.5 Granular Activated Carbon Cartridge. Sediment Filter is often the first filter installed in the Whole House Water Filter circuit. It is often the first point of contact between your water supply and your home and is used as a pre-filtration unit before the water continues to reverse osmosis and activated carbon filters. It catches unwanted particles, including sand, dirt, silt, rust, and other fine particles as they attempt to enter your house’s water system. These particles and pollutants come from water sources, old and dirty pipes, as well as contaminants that are used to treat the water. 10″ x 4.5″ filters are made of fine-melted polypropylene that are blown and spun into cylinder-like form. Removal of these particles allows filters, such as Carbon Block or GAC (Granular Activated Carbon) filters, as well as household water appliances like boilers, refrigerators, ice-makers, and many more, to perform better for longer periods of time. Pleated sediment water filters reduces sand, dirt, silt, rust, & scale particles in residential and commercial water. Pleated filters are made of resin-impregnated cellulose and polyester media pleated around a polypropylene core for strength. These materials trap suspended particles, materials that block microbes and adsorb unwanted chemicals or substances that cause a chemical change to the water, such as acid neutralization. The pleated design provides an amplified surface area that may extend the filter’s life while removing undesirable particles and chemicals from the water by means of a semipermeable barrier, adsorption, & biological processes. Those filters are washable & reusable. Advantage of pleated filters is that they protect against a lower pressure drop & allow increased water flow rates. Pleated cartridges outperform standard wound, spun, & melt blown filters because of their re-usability. Activated Carbon Block filters are made of fine coconut shell carbon. They remove odors, undesirable colors, and unpleasant tastes of many organic compounds. These filters also are effective in removing chemicals like iron, manganese, chlorine, and hydrogen sulfide from your water to name a few. By removing these unwanted byproducts, you can rest assured that you will have access to fresh and clean water. Since these filters are made of a finely packed carbon (forming a cylinder block), they offer a much finer filtration of suspended particles and dirt. Chlorine removal is what carbon is best at, and nothing else equals carbon’s ability to remove chlorine. Granular Activated Carbon filters are made of fine coconut shell carbon. All Ronaqua GAC filters are made with high quality coconut shell carbon crushed into positively charged granules. The positively charged granules in the filter remove negative ions from the water, such as: chlorine, fluorides, ozone, and dissolved organic solutes, effectively providing good general-purpose drinking water. High Capacity 10 x 4.5 Whole House Filter Purifier System can purify the water coming into your home for Well Water and Municipal Tap Water. It can deliver effective protection for the pipeline, water purifier, water heater, wall hung gas boiler, washing machine, dishwashers, showers, and other terminal water appliances. Protect Your Home and Appliances. Improve Your Life by Providing Clean Drinking Water. Forget about dirty bad-smell and bad-tasting water. High capacity water filtration system will efficiently remove sediment, large and fine particles, chlorine, odors, and tastes of many organic compounds extend the service life of water heaters, washing machine, dishwashers, reverse osmosis systems, and all plumbing fixtures. Our individually designed whole house water filtration system by removing, chlorine, and other contaminants, provide clean and fresh water for your family, protect your loved ones, and reduce the use of bottled water. We are proud to deliver the perfect water your household and safe our Planet by reducing use of the plastic bottles. These housings made from food grate material and meet NSF (National Science Foundation) standards and regulations. Tanks to durable construction, and easy maintenance those housings can be used in many different applications.
10×4.5 Big Blue 2-Stage Whole House Water Filter Filtration System Brass Port
Brass NPT Thread+Dual O-Ring. SimPure 2-stage whole house water filter system has upgraded the material at the connection points, replacing plastic with. Significantly extending the product’s lifespan. In addition, we also utilize dual O-ring seals, which effectively reduce the risk of leaks and ensure a tighter seal at the connection points. The SimPure SPWH-2S Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Main Features: With our instruction you can use and install SPWH-2S 2-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Clear Housing help you to know which filter and when you need to change. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections. To ensure watertight seal. Visible Clear Housing: Our well water filter system for the house consists of two. Standard transparent filter housing, which allows you to monitor the filter cartridge usage anytime, anywhere, making it more convenient than traditional blue filter housing. They are made of reinforced polypropylene for strength and resistance to chemicals. Furthermore, we’ve improved the quality of the filter bottles by increasing their thickness and durability. The Ultimate 2-Stage Filtration : SimPure home water pre-filtration system is compatible with most standard 10″ x 4.5″ filter cartridges and provides excellent filtration performance. It can provide you and your family with up to. Of clean water for a year. Additionally, filtered water contributes to preserving your health and prolonging the lifespan of your appliances. You can connect it to municipal or well water. Suitable for homes, RVs, boats, mobile homes, and gardening. This SPWH-2S water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. Longer Lifespan: The carbon filter has a lifespan of. While the sediment filter can last for. Of course, the specific duration depends on your water quality. With a 5? M filter pore size, it effectively removes sediment, rust, dust, and large impurities from the water, reducing odors, discoloration, and chlorine, resulting in improved taste. We recommend a water pressure of 25-90 psi and a temperature range of 41-100°F. Remove dirt, silt, sand, rust and scale particles, etc. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Big Clear Housing let you know when to replace the filters. The pressure relief Valve: Let you replace the filter cartridges easily. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. 1 Female NPT Thread. 14.3″L 7.6″W 15.4H. 10 4.5 Inch. MAX 15 Gallons (57L) Per Minute. Sediment Filter 3-6 Month, Carbon Filter 6-12 Month. 100% food-grade ABS + Metal + Stainless Steel. Make sure the connection is correct and check for water leaks. 1x SPWH-2S assembled housing kit with bracket. Filters(1PP sediment+1CTO filters). 2x Plastic Expansion Nail. 4x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Extra 1 Set Filter: 1x Extra PP Filter 1x Extra CTO Filter. Extra 2 Set Filters: 2x Extra PP Filters 2x Extra CTO Filters. Extra 3 Set Filters: 3x Extra PP Filters 3x Extra CTO Filters. Not all of the items are included in the package, please choose the “Item Type” you need in the selection. SERVING USA SINCE 2006. SimPure dedicated in providing world-class quality of water filtration solutions. Please contact our trained water specialists. And is available to answer any questions during the life of the product.