stage
4 Stage Whole House Ultra filtration 0.01 Micron UF Drinking Water Filter System
4 Stage Whole House Ultra filtration 0.01 Micron UF Drinking Water Filter System.
3 Stage Whole House Water Filters Express Water Filters $250
3 stage filters with instructions included. HAVE THE CLEANEST, MOST HEALTHY WATER YOU CAN DRINK!
3 Stage RV Water Filter System with Leak Proof Double O-Ring with 3/4 Hose Fittings
RV Water Filter System that’s Economical with 3 Stage’s for extra clean tasting water. This system flows Left to Right.. This RV water filter system comes with a newly designed housing, made of the highest quality FDA Approved Reinforced Polypropylene. Outstanding Burst limit pressure of above 360+ PSI and high flow rate. (What’s in the Box:). 3 Stage Water Filter System. 1 x Heavy Duty Steel Hanging Bracket. 3 x White Connected Filter Heads 3/4 FNPT Threaded Ports with Red Pressure Release Values. 2 x 1 Threaded Filter Head Fittings. 3 x White Filter Housings with Leak Proof Double O-Rings. 1 x Sediment Filter. 1 x UDF Carbon Filter. 1 x CTO Carbon Filter. 1 x Housing Wrench. 1 x 3/4 Male Hose Fitting. 1 x 3/4 Spinning Female Hose Fitting. 1 x Roll of Teflon Tape. This RV System Cleans the water that enter’s your Recreational Vehicle. 1st stage: 10 Premium PP Polypropylene. 1 Micron sediment filter. Removes dust, dirt, silt, sand, Iron, rust and scale particles in the filter and extends the life of the system. 2nd stage: 10 Premium UDF/GAC Granular Activated Carbon. 5 Micron Filter removes chlorine, Sulfur, radon, VOCs, Pesticide’s and other common chemicals. This filter also removes cloudiness, offensive odors, colors and improves taste. 3rd stage: 10 Premium CTO Carbon Block. 5 Micron Filter removes chlorine, Sulfur, radon, VOCS, insecticides, pesticides, industrial solvents and improves taste. Working pressure: 20 to 125 psi water pressure. White Housing design that accepts standard 10″ x 2.5″ filter cartridges. Made to NSF Standards. Just unwrap the filters and reinstall in housings. This water filter system is not returnable if system has been used.
3 Stage 4.5 x 20 Whole House Water Filter System, Sediment & Carbon, 1 Port
SimPure DB20P-3 20″ x 4.5″ 3 Stage Big Blue Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges & Pressure Relief Valve- GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue 20″x4.5″ Whole House Water Filter System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.
3 Stage Whole House Water Filter System 4.5 x 20 Filtration System Big Housing
SimPure DB20P-3 20″ x 4.5″ 3 Stage Big Blue Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges & Pressure Relief Valve- GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue 20″x4.5″ Whole House Water Filter System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 3x Extra Filters for Replacement (PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.
3 Stage Whole House Water Filter Sediment Carbon Filter 20×4.5+ Pressure Gauge
SimPure DB20P-3 20″ x 4.5″ 3 Stage Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges & Pressure Relief Valve- GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue 20″x4.5″ Whole House Water Filter System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.
3 Stage 20 Inch Whole House Water Filter System Housing + 3 Set Filter Cartridge
SimPure DB20P-3 20″ x 4.5″ 3 Stage Big Blue Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges – GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue 20″x4.5″ Whole House Water Filtration System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters with easy thanks to Pressure release buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. DB20P-3 Water Filter System — 1x DB20P-3 Water Filter System with all accessories. DB20P-3+1 Set Filter Cartridge — 1x DB20P-3 Water Filter System with all accessories + 1x Set Extra 20″ x 4.5″ filter(1:Sediment filter 1: GAC filter 1:CTO filter). DB20P-3+2 Set Filter Cartridge — 1x DB20P-3 Water Filter System with all accessories + 2x Set Extra 20″ x 4.5″ filter(2x Sediment filter 2x GAC filter 2xCTO filter). DB20P-3+3 Set Filter Cartridge — 1x DB20P-3 Water Filter System with all accessories + 3x Set Extra 20″ x 4.5″ filter(3x Sediment filter 3x GAC filter 3xCTO filter). 1 Set Filter Cartridge — 1x Set Extra 20″ x 4.5″ filter for DB20P-3 replacement(1:Sediment filter 1: GAC filter 1:CTO filter). 2 Set Filter Cartridge — 2x Set Extra 20″ x 4.5″ filter for DB20P-3 replacement(2x Sediment filter 2x GAC filter 2x CTO filter). 3 Set Filter Cartridge — 3x Set Extra 20″ x 4.5″ filter for DB20P-3 replacement(3x Sediment filter 3x GAC filter 3x CTO filter). Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Check the filter cartridge has not been installed incorrectly. Make sure the plastic wrapper around the filter has been removed. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: Water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used).
3 Stage Whole House Water Filter System 1 Port With Bracket 20-Inch Big Blue
SimPure DB20P-3 20″ x 4.5″ 3 Stage Big Blue Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges – GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue Whole House Water Filtration System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters with easy thanks to Pressure release buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 filter housing. 1x Set 20″ x 4.5″ filter cartridge element inside the filter housing(1:Sediment filter 1: GAC filter 1:CTO filter). 1x Filter bowl wrench. 2x Plastic Expansion Nail. 2x O-rings inside the filter housing(Both to install on each filter housing). 1x Punch positioning sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Check the filter cartridge has not been installed incorrectly. Make sure the plastic wrapper around the filter has been removed. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: Water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used).
4 Stage Whole House Ultra filtration 0.01 Micron UF Drinking Water Filter System
4 Stage Whole House Ultra filtration 0.01 Micron UF Drinking Water Filter System.
3 Stage Whole House Water Filter System with Leak Proof Double O-Ring 1 Port
Whole House Water Filter System that’s Economical with 3 Stage’s for extra clean tasting water. This system flows Left to Right and by turning the bracket around this system will flow Right to Left if needed. This whole house water filter system comes with a newly designed housing, made of the highest quality FDA Approved Reinforced Polypropylene. Outstanding Burst limit pressure of above 360+ PSI and high flow rate. (What’s in the Box:). 3 Stage Water Filter System. 1 x Heavy Duty Steel Hanging Bracket. 3 x Black Connected Filter Heads 1 FNPT Threaded Ports with Red Pressure Release Values. 2 x 1 Threaded Filter Head Fittings. 1 x Clear Filter Housings with Leak Proof Double O-Rings. 2 x Blue Filter Housings with Leak Proof Double O-Rings. 1 x Sediment Filter. 1 x UDF Carbon Filter. 1 x CTO Carbon Filter. 1 x Housing Wrench. This Whole House System Cleans the water that enter’s your home. 1st stage: 10 Premium PP Polypropylene. 1 Micron sediment filter. Removes dust, dirt, silt, sand, Iron, rust and scale particles in the filter and extends the life of the system. 2nd stage: 10 Premium UDF/GAC Granular Activated Carbon. 5 Micron Filter removes chlorine, Sulfur, radon, VOCs, Pesticide’s and other common chemicals. This filter also removes cloudiness, offensive odors, colors and improves taste. 3rd stage: 10 Premium CTO Carbon Block. 5 Micron Filter removes chlorine, Sulfur, radon, VOCS, insecticides, pesticides, industrial solvents and improves taste. Working pressure: 20 to 125 psi water pressure. Blue Housing design that accepts standard 10″ x 2.5″ filter cartridges. Made to NSF Standards. Just unwrap the filters and reinstall in housings. This water filter system is not returnable if system has been used.