Monthly Archives: September 2023
Whole House Fluoride Removal Water Filter BONE CHAR -1 Cubic Ft + In/Out 9x48T
If you want to remove fluoride from more than just your kitchen sink, a whole house system will work for you. This system removes fluoride from every faucet with one convenient system. This whole house with 1 cubic foot of bone char. You can also choose to add on a 10 Big Blue housing sediment prefilter (recommended). 1 cubic foot of bone char will remove approximately 1.0 mg/l of fluoride. Bone char is known to be one of the most effective methods to remove any type of fluoride from your drinking water. Bone char is also very effective removing heavy metals, pesticides and chlorine. 1 Cubic Foot System: 9″ x 48″ inch Mineral Tank IN/OUT Valve. 1 CUBIC FOOT OF BONE CHAR FLUORIDE REMOVAL MEDIA – Pre-filled in Tank. WHOLE HOUSE 1 CU FT BONE CHAR CARBON + IN/OUT VALVE. This system is easy to set up. With this system you will receive. 9″ x 48″ FRP Vessel. Colors Black/Blue/Almond IN/OUT Valve 1 CU FT Bone Char Blend Carbon Pre-filled in tank 1 In/Out ports. The use of bone charcoal or bone char is reported to be an effective means for the reduction of fluoride. Bone charcoal contains a carbon structure while supporting a porous hydroxyapatite matrix (a calcium phosphate hydroxide in crystalline form which is rich in surface ions which can be readily replaced by fluoride ion). This filter works like regular carbon as well. A whole-house filter system treats all water traveling to any faucet or fixture in the home. It removes the chemical before it can be ingested, breathed in, or absorbed by the skin during washing or bathing. A larger carbon filter like this one provides better filtration because of the amount of carbon, and depth of the filter bed. It does not cause a water pressure drop in your home compared to solid block carbon filter installed at the point of entry. Carbon removes/reduces many volatile organic chemicals (VOC’s), pesticides and herbicides, as well as chlorine, benzene, trihalomethane (THM) compounds, radon, solvents and hundreds of other man-made chemicals found in tap water. Carbon is a substance that has a long history of being used to absorb impurities and is perhaps the most powerful absorbent known to man. One pound of carbon contains a surface area of roughly 125 acres and can absorb literally thousands of different chemicals. Activated carbon which has a slight electro-positive charge added to it, making it even more attractive to chemicals and impurities. This filter contains 2 cu ft of bone char media. What else can it remove? Bone char can not only reduce fluoride, it can also reduce or remove cadmium, lead, iron, manganese, mercury, zinc, copper, nickel, aluminum, arsenic, fertilizers, radio-nuclide, herbicides, pesticides, radium and uranium. It’s also been shown to remove tributyl tin oxide, nuvan and malochite green. How long does it last? Point of use fluoride filter systems can handle about 5,000 gallons before a filter change, while whole house systems can handle about 100,000 gallons. This varies depending on your use and fluoride levels but the average four person family should only need an annual filter change. By having bulk bone char on hand you can change it out at any time.
Whole House Water Filter System 4.5 x 20 Big Blue 3 Stage Filtration 1 Port
SimPure DB20P-3 20″ x 4.5″ 3 Stage Big Blue Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges & Pressure Relief Valve- GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue 20″x4.5″ Whole House Water Filter System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.
ISpring WSP50J Reusable Whole House Spin-Down Sediment Water Filter, Jumbo Size
The WSP-J series spin down sediment filter is the first line defense to your appliances. It protects and extends the life of your standard filters by removing the large dirt, sand, and rust particles before they reach the rest of your plumbing system, including water softeners and expensive appliances. The WSP series is flushable and reusable. It is recommended to flush it regularly (daily or weekly), depending on the water usage, sediment amount and the hardness level. However, as hardness tends to form hard scale that clogs the screen, simple flushes may not be sufficient. When necessary, remove the stainless steel cartridge and clean it with a brush and/or soak it in vinegar. Please avoid the mistake of using’fine’ filters for’rough’ water and causing the filters to clog sooner than expected. Use multi-stage filters to achieve one of the best filtering result and longer cartridge life.
3-Stage 20×4.5 Whole House Water Filter System Sediment Carbon Filter Gauge
SimPure DB20P-3 20″ x 4.5″ 3 Stage Whole House Water Filtration System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges – GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue Whole House Filtration System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.
Whole House Water Filter System 4.5 x 20 Filtration System Housing +1Yr Filter
SimPure DB20P-3 20″ x 4.5″ 3 Stage Big Blue Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges & Pressure Relief Valve- GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue 20″x4.5″ Whole House Water Filter System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 3x Extra Filters for Replacement (PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.
1/5/10/20 Micron 20×2.5 PP Sediment Water Filter Whole House Commercial 1-50PK
20 inches x 2.5 inches 1/5/10/20 micron polypropylene sediment filter cartridge. Compatible with a wide rage of industrial filter housings and the whole house filter housings. The sediment filter cartridge is made of. Which cause no pollution to water. Food grade material, non toxic and tasteless. Keep water clean and fresh, provide a healthy life for you and your family. Remove 99% rust, silt, sand, iron and other undissolved particles in dirty water. As the first line of defense in the filtration system, protect your water using appliances and plumbing for cleaner water, improve water quality and taste. Compare to string wound filter, this filter using unique hot melt technology, no fibers falling, avoid second pollution to liquid. Our replacement water filter cartridge is verified by independent laboratory tests, compliance with. Food-grade materials, BPA Free. For better water quality, recommended replace. TWO or THREE times a year. Depending on the quality of the original water source and application type. Recommended change out differential pressure is 30psi(2.1bar). Three separate gradient density layers enhance cartridge performance, higher dirt-holding capacity than the similar sized sediment water filter. Dimensions: 20 inch x 2.5 inch (508mm x 63mm). Inner Diameter: 1.1 inch (28mm). Flow Rate: 8 GPM. Operating Pressure at 158? Operating Pressure at 68? Compatible for GE, Aquasana, Flow-Pro 3M, GE, Culligan, Dupont, Pentek, Omni, Kenmore, Omnifilter, Whirlpool, Filtrete, etc. Fits most of 20 inch slim filter housing. It is widely used in whole house filtration system, as pre-filter for water softener system. Compatible for Clack Corporation 31052000, Flow-Pro FPMB6-20, GE Hytrex GX05-20, GE Osmonics MB-05-20, 1013240, GE Purtrex PX05-20, Aquasana EQ-304-20, etc. What is a sediment water filter cartridge? It’s usually placed as the first stage of the water filtration system to remove rust, iron, sand, silt and particulates from water. As the first line of defense in the filtration system. It’s a best choice for removing fine sediment from well water / hard water / city water / municipal water / drinking water, etc. The unwanted particles found in water are measured in microns. How to choose the right size? If you choose the right size for your housing, there are not great influence on the flow rate when you replace them. The size is small: there is a significant drop in flow rate. The size is large: there is still some sediment in your water. Please make sure the size is meet your need before ordering. The important thing to know about sediment filters is that they only reduce sediment. They don’t remove chemicals or heavy metals or make the water taste or smell better. 1 Pack: 1x Water Filter. 2 Pack: 2x Water Filters. 4 Pack: 4x Water Filters. 6 Pack: 6x Water Filters. 12 Pack: 12x Water Filters. 20 Pack: 20x Water Filters. 25 Pack: 25x Water Filters. 50 Pack: 50x Water Filters.
3 Stage Whole House Water Filter System 4.5 x 20 Filtration System Big Housing
SimPure DB20P-3 20″ x 4.5″ 3 Stage Big Blue Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges & Pressure Relief Valve- GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue 20″x4.5″ Whole House Water Filter System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 3x Extra Filters for Replacement (PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.
1-100PK 1 Micron 10×2.5 Sediment Water Filter Whole House Farm Well Replacement
Polypropylene Sediment Water Filter Replacement Cartridge. Excellent choice to filter sediments from the potable well or tap water. As the first line of defense in the filtration system, it can effectively prevent the clogging of water pipes and prolong the service life of water equipment. Material Safety: 1 micron water filter made of 100% pure polypropylene material, it meets the NSF certification, ISO9001, BPA free. There is no fibers shedding because of unique melt-blown technology to avert the re-contamination of drinking water. Provide your family with much safer and healthier life all the time. Protect Water Equipment: This sediment water filter removes 99% rusts, silts, sands and other undissolved particles, etc, from dirty water. As the first-stage filter in the filtration system, it protects your post-filters, water appliances and pipes with purer and higher quality water, providing a healthy life style. 6 Months Service Lifetime: 10 inch water filter cartridge usually filtrate water up to 10,000-15,000 gallons. The filtration capacity and change-out cycle depend on inlet water quality or running time every day. For better water quality, filters should be replaced regularly. Multi-Layer Structure: Our micron filter has three separated gradient density layers to filtrate sediments deeply and enhance excelent performance and higher dirt-holding capacity than the similar size sediment water filter. In other words, it has a longer service lifetime. NSF Certified: This MPP Filter is tested and certified by NSF International against NSF/ANSI Standard 42 for material requirements only. Standard Universal Filter: Whole house water filter fits most of Reverse Osmosis Systems, Under Sink Filtration Systems and any Whole House Water Filtration Units with 10-inch filter housings. Compatible with standard 10″x2.5″ filter models of Culligan P5, Aqua-Pure AP110, AP110-NP, DuPont WFPFC5002, CFS110, OMNIFilter RS14, Whirlpool WHKF-GD05, American Plumber WC34-PR, GE FXUSC, etc. Compatible with Aqua Pure AP110, AP110-NP, AP101S, AP101T, AP11S, AP11T, AP12S, AP1610, AP2610, AP51T, SS1-SS12, SS20-SS36, GE FXUSC, Whirlpool WHKF-GD05, WHKF-DWHV, Culligan P5, P5-D, P5A, HF-150, HF-160, HF-360 and DuPont WFPFC5002. Widely fits most 10-in x 2.5-in whole house drop-in style filter systems from major brands including 3M, GE, Culligan, Dupont, OMNIFilter, APEC, Olympia, US Aqua, Aquasana, Costway, Whirlpool, Smart Aqua Life, Geekpure, and others. Compatible for 3M 70020143163, AquaPure AP802, AP802-1.5, Cuno 5557610, CFS02T. Systems from 3M, DuPont, APEC, Whirlpool, Olympia, US Aqua, Pentek, Aquasana, Culligan, Costway, GE, Smart Aqua Life, Geekpure, The Perfect Water, Glacier Bay, Aqua-Pure, Global Water, etc. Pre-filtering treatment of many filtration systems, like Whole House Water Filtration System, Well Water Filtration System. Widely used for food and beverage industry, like Beer and Wine, Maple Syrup, Edible Oil, and Drinking Water, etc. Product Inner Diameter in. 15,000 (depending on water condition). Typical service life is 3-6 months depending on volume filtered and sediment levels. Recommended service temperature:40-113°F/5-45? Flush 5 gallons of water through the filter before use. For spun or wound string filters, they can be used interchangeably. The important thing to know about sediment filters is that they only reduce sediment. They don’t remove chemicals or heavy metals or make the water taste better. 1 PACK: 1x Water Filter. 2 PACK: 2x Water Filters. 4 PACK: 4x Water Filters. 6 PACK: 6x Water Filters. 8 PACK: 8x Water Filters. 10 PACK: 10x Water Filters. 12 PACK: 12x Water Filters 20 PACK: 20x Water Filters 25 PACK: 25x Water Filters 50 PACK: 50x Water Filters 100 PACK: 100x Water Filters. Not all of the filters are included in the package, please choose the “QUANTITY” you need in the selection. After you received them. Returning items should include original package, invoice, accessories. Membrane solutions was established in the United States in 2006 and is headquartered in Texas. Committed to the research and development and production of microfiltration, ultrafiltration and reverse osmosis membranes and water purification products. Membrane solutions is committed to. Offering our customers exceptional selection and value. Providing the highest quality of service and products in the water treatment industry. Satisfying our customers with superior quality water filtration products that will lead to a healthier lifestyle. F you have any problem of the goods, please. Promise we will try our best to deal with your problem. We appreciate your patience and supports. Thank you for choosing us and have a great day!
3 Stage Whole House Water Filter Sediment Carbon Filter 20×4.5+ Pressure Gauge
SimPure DB20P-3 20″ x 4.5″ 3 Stage Whole House Water Filter System (1 Inlet/Outlet Port) with Big Housings & Pressure Gauges & Pressure Relief Valve- GAC Filter, Carbon Block, Sediment Filter Cartridges – Whole Home Water Filters Portable Steal Frame. SimPure DB20P-3 3 Stage Big Blue 20″x4.5″ Whole House Water Filter System. The SimPure DB20P-3 is a 3 Stage Whole House Filtration System(PP Sediment + GAC + CTO). 1st filter (PP sediment filter) can remove dirt, silt, sand, rust and scale particles. The 2nd-stage filter (GAC granulated activated carbon filter) can remove chlorine, chloramine, VOCs and etc. The 3rd- filter(CTO carbon block filter) can remove chlorine, chloramine, VOCs, bad taste and odor. Extend the life of your dishwasher and other appliances, and reduce cost of the energy. With our instruction you can use and install DB20P-3 3-stage whole house water filtration system with no problem. Housing Bracket so You can choose mounted or unmounted installation. Pressure gauges help to monitoring your system and to know which filter you need to change and when. Remove the filters easily by the Pressure Release Buttons. The black cap has 1 female National Pipe Thread Taper (NPT) threaded input and output connections, DOUBLE O-ring to ensure watertight seal. This DB20P-3 water filtration system connects directly to your home’s main water supply and fits standard American plumbing with 1 NPT inlet and outlet. It comes with a installation and maintenance guide. And It Is Easy to Replace Water Filter Cartridges: All SimPure Water whole house water filter replacement cartridges are designed for quick and easy replacement to keep your system up and running. The SimPure DB20P-3 Water Whole Home Water Filtration Systems is constructed with standing stainless-steel frames for long term durability and quality. Stage 1: PP Sediment Filter. Remove dirt, silt, sand, rust and scale particles , etc. Stage 2: GAC Filter. Remove chlorine, chloramine, VOCs, etc. Stage 3: CTO Filter. Remove chlorine, chloramine, VOCs, bad taste and odor, etc. Double O-Ring ensure watertight seal. Three accessible pressure release buttons for easy filter change. Three pressure gauges: Monitor your system’s performance, know which filters you need to change and when to change them. Standard 1 female NPT thread connections and long high efficiency housings for easy adaptability and high flow. Material: 100% food-grade ABS + Metal + Stainless Steel. Filter Size: 20 4.5 Inch. Filter Life (Months): 6 Month. Flow Rate (GPM): 15 GPM. Inlet/outlet Connection: 1 female NPT thread. Pressure Range: 25 – 90 psi. 1x DB20P-3 assembled housing kit with bracket. 3x Installed Filters(PP sediment+GAC+CTO filters). 2x Plastic Expansion Nail. 6x Installed O-rings (2 in each housing). 1x Punch Positioning Sticker. Q: Leaks between filter head and filter bowl of housing A1: Tap water pressure is too high; make sure it is below 90psi (620kpa). If too high, fit a pressure regulator. A2: The O-ring may not be in place. Clean and lubricate O ring with silicone grease. Also, clean the groove where the O-ring sits. Replace O-ring in the groove above threads. Screw the bowl back on the filter head securely by hand, then use the wrench to fit it snugly. Do not over tighten. Q: Leaks on inlet/outlet connections A1: Wrap the Teflon tape around pipe threads of each fitting in a clockwise direction, add more tape as necessary for the correct seal. A2: Brass fittings may require to tighten ½-turn with a wrench. Q: Leaks from the pressure release button A: The pressure release button has a screw under the bracket. Simply tighten that screw and the leaking should stop. Q: Water Pressure is slowing after some time A: Recommended changing the cartridges every 6-12 months depending on the amount of contaminants present in the feed water supply. If the system has been working correctly and the water pressure is slowing, it may be time to change the filter cartridge element. Q: Water Pressure is slowing immediately after installation when using a Carbon Cartridge A1: Make sure the plastic wrapper around the filter has been removed. Check the filter cartridge has not been installed incorrectly, especially the GAC filter, please look at the picture, this is the botttom side of the GAC filter. A2: Bathtubs, utility sinks, garden hoses, showers, or anything considered high-flow should be avoided for the first 72 hours. Any high-flow situation within the first 72 hours may cause a temporary carbon blockage. To clear the blockage, turn off any running water for at least 10 minutes and resume using water at low or regular flow rates. Q: Water appears cloudy and grey A: The water may appear cloudy or grey for the first 3-5 days after installation due to the tiny air bubbles being purged from the filters and extra carbon dust in the water. (depending on the filter cartridge being used) To solve this problem, please flush the whole system for about 10 minutes after you install it, then close the faucet and wait for one hour. And repeat the steps until the output water is clean.