Pentair Fleck Whole House Water Softener (Upgraded 10% Resin & Steel Valve)

Pentair Fleck Whole House Water Softener (Upgraded 10% Resin & Steel Valve)

Posted on April 10, 2018 Tag by  , , , , , , , , , Category in  pentair
Pentair Fleck Whole House Water Softener (Upgraded 10% Resin & Steel Valve)
Pentair Fleck Whole House Water Softener (Upgraded 10% Resin & Steel Valve)
Pentair Fleck Whole House Water Softener (Upgraded 10% Resin & Steel Valve)

Pentair Fleck Whole House Water Softener (Upgraded 10% Resin & Steel Valve)
PENTAIR FLECK METERED SOFTENING KITS – Water Softener (VALUE). Great Value, Water Softener. FLECK 5600 “SXT” METERED SOFTENING KIT Kit Includes. Pentair Fleck control valve. Mineral Tank (Black, Almond or Blue) 10″x 54″. 3/4 Bypass (Stainless Steel). C150 Resin 1 1/2 CU FT 68 lbs. 18 X 33 Brine Tank. Distributor Assembly W/ Upper and Lower Screens. Utilizes 8% Cross link Cation Resin/#8 Garnet. Solid State Microprocessor W/ LED Display. Time of day, Remaining capacity & regeneration cycle in progress. Down flow & Up flow regeneration cycles. 3 Modes of operation: Delayed Meter Regeneration, Delayed Time or Clock Regeneration. NOVRAM Valve status & memory back up. Working PSI 20 – 125PSI. Water Softener is an Ion Exchanger. Hard Water with a high calcium/magnesium content enters the softener through the “in” port indicated by the green arrow. It passes through the control valve and in to the tank where it goes from top to bottom through a specially prepared resin that “softens” it, the resin consists of specially manufactured beads that have been saturated with sodium ions. Softening occurs as the hardness minerals in the water attach themselves to the resin and are “exchanged” for sodium. The softened water then enters the long center tube called a riser, via the strainer basket at the bottom of the tank and passes upward through the riser. Then water exits the softener via the control valve (Blue Arrow) and is sent to the desired location. When the resin becomes saturated by hardness minerals, the softener automatically goes into re-generation. The re-generation process is initiated by a time or a meter depending on the type of softener. By this process the hardness minerals are washed down the drain and resin bed is rinsed, re-settled and re-charged with sodium, it is now ready again to soften your water. The re-generation process is accomplished by passing very salty water from the brine tank through the resin. The brine tank must remain filled with softener salt at all times so that it can re-generate the softening resin. The following conditions for feedwater supply must be met. RO System must be connected to a municipal or well water source that is treated and tested on a regular basis to insure bacteriologically safe water. Operating Temperatures : A Maximum 113° F B Minimum 39° F 3. Operating Pressure : A Maximum 115 PSI (5.95 kg/cm2) B Minimum 40 PSI (2.95 kg/cm2). Do not allow RO System to freeze. The membrane always contains water and will be destroyed if frozen. Do not plumb RO System to hot water. This will destroy the integrity of system components. If pressure B 40 BelowA pressure regulator is advised to maintain proper pressure. Personal checks may be held until cleared. ITEMS DO NOT INCLUDE INSTALLATION GUIDE UNLESS SPECIFIED. The item “Pentair Fleck Whole House Water Softener (Upgraded 10% Resin & Steel Valve)” is in sale since Sunday, June 12, 2016. This item is in the category “Home & Garden\Kitchen, Dining & Bar\Small Kitchen Appliances\Water Filters”. The seller is “waterproshop.usa” and is located in Cypress, California. This item can be shipped to United States.
  • Brand: Penter Fleck, Evertech,
  • Country/Region of Manufacture: United States
  • Country of Manufacture: United States
  • MPN: Does Not Apply
  • Number of Filtrations: 2

Pentair Fleck Whole House Water Softener (Upgraded 10% Resin & Steel Valve)